We may earn a commission when you buy through our links. How we make money
This guide is general and applies in all three countries. Prices differ by store and country, and we give none here; see our Elegoo guide for dated prices in the UK, Germany and the US.
3D printing sounds technical, but a first print is a short list of steps. The decision that matters most comes before you buy anything: whether to start with a filament printer or a resin printer. This guide helps you make that choice, tells you what else to have ready, and walks through a first filament print.
- Start with a filament (FDM) printer. It has a gentler learning curve, simpler safety needs and a quicker first print. Choose resin first only for miniature-grade detail.
- Start with PLA filament: it is forgiving and does not need an enclosure.
- Get a printer with automatic bed leveling and use the slicer its maker recommends. Watch the first layer.
- Resin is hazardous until cured: gloves, eye protection, ventilation, washing and curing all apply.
- We have not tested printers for this guide. It is built from the sources listed at the end, two of which are makers’ own guides.
Filament or resin
Resin prints are finer: smoother surfaces and sharper small detail, which suits miniatures and jewellery. Filament printers build larger: typical home filament printers are about 220 to 300 mm across and home resin printers usually 150 to 220 mm. Filament is cheaper to run and quicker to finish: an FDM print needs about 5 minutes of support removal and optional sanding, while a resin print needs 20 to 30 minutes of washing in isopropyl alcohol, UV curing and support removal. One comparison estimates first-year entry-level costs at about $440 for filament and $750 for resin.
Safety differs too. PLA on a filament printer is low-emission and fine in a ventilated room, while materials such as ABS, ASA and nylon need an enclosure with filtration. Resin needs gloves, eye protection, a respirator and venting outside, and should not be used in a bedroom or kitchen. The usual recommendation for beginners is filament.
What else you will need
| You need | Why |
|---|---|
| PLA filament | The usual first material for a filament printer. It is forgiving and does not need an enclosure. |
| The slicer your printer’s maker recommends | Software that turns a 3D model into layers for the printer. Free options include Bambu Studio, OrcaSlicer, PrusaSlicer and Cura. |
| A flat, clean build plate | Handle it by the edges: skin oil hurts adhesion. |
| Flush cutters, and optional sandpaper or paint | To cut away supports and strings and to smooth a finished part. |
| Isopropyl alcohol, gloves and eye protection (resin only) | To wash uncured resin from parts safely. |
| A ventilated room and a smoke alarm nearby | Safety basics: do not leave early prints unattended. |
We give no prices because they differ by store and country and change often. Our Elegoo guide lists dated prices for four printers and for filament, resin and a wash and cure station in the UK, Germany and the US.
Your first filament print
Choose a printer with automatic bed leveling, a direct-drive extruder and a removable flexible build plate, and an enclosed model if you plan to print ABS or ASA. Unbox it and set it up, then run its first-time calibration: bed leveling is the step that matters most, and many printers do it automatically. For a manual check, slide a sheet of paper under the nozzle and aim for a slight drag.
Preheat the nozzle to the temperature your filament needs, which is printed on the spool or the maker’s page, and feed the filament into the extruder. For PLA, guides give the nozzle at about 200 to 220 °C and the bed at about 55 to 65 °C. Load a model that many people have printed successfully into the slicer, choose your printer’s PLA profile and the default 0.2 mm layer height, and add supports only for overhangs steeper than about 45 degrees. Send the file to the printer and start.
Stay for the first layer. The lines should be slightly squished and joined to the plate. Round, separated lines mean the nozzle is too high, and rough, see-through lines mean it is too low. If the nozzle scrapes or the lines blur together, stop and adjust. When the print is done, let the bed cool, because the part often releases on its own, and bend a flexible plate gently to pop it off. Then cut away supports with flush cutters.
When a print goes wrong
| What you see | Likely cause |
|---|---|
| The print does not stick or comes loose | Dirty plate or nozzle too high above it |
| A tangle of filament (“spaghetti”) | The part came loose, or the supports failed |
| Fine strings between parts | Wet filament, or temperature too high |
| Corners lift | Shrinkage or drafts |
| A flared bottom edge | Nozzle too low, or bed too hot |
| Layers shifted | Loose belts or a collision |
| Thin walls or no filament coming out | A clog or under-extrusion |
Software can be the weak point as well as hardware. A review of the Elegoo Centauri Carbon 2 Combo on Notebookcheck praised the printer but found the connection to its slicer inconsistent and print-time estimates off by more than 17% on some multicolour prints. Expect to spend time with the slicer, whichever printer you buy.
- A filament printer with automatic bed leveling for your first printer.
- PLA filament and your printer maker’s own slicer for the first prints.
- A resin printer only if you want miniature-grade detail and have a ventilated space, gloves and eye protection.
- Resin as a first printer if you have no safe space for it: not a bedroom or kitchen.
- ABS or ASA at the start: they need an enclosure and filtration.
- Leaving early prints unattended: watch the first layer and keep a smoke alarm nearby.
Questions people ask
Is resin or filament better to start with?
The usual recommendation is filament. It has a gentler learning curve, simpler safety needs and a quicker first print. Resin has a steeper learning curve and costs more to set up, and suits you if you specifically want miniature-grade detail.
What filament should I use first?
PLA. Guides call it forgiving, and it does not need an enclosure. ABS, ASA and nylon need an enclosure with filtration.
Why does my first layer matter so much?
A poor first layer is the usual reason prints fail to stick. Guides stress bed leveling and a clean plate, and say to stop and fix the first layer rather than let a bad print continue.
Do I need a special room?
For PLA, a ventilated room is enough. For resin, safety guides advise venting outside, gloves, eye protection and a respirator for long sessions, and say not to use resin in a bedroom or kitchen.
How long does a first print take?
It depends on the model. It depends on the model and the settings, and the sources we read give no single figure. In 3DWithUs’s test of one Elegoo printer, most prints took 1 to 5 hours at the default settings.
Sources
- 3DPrinting.com: FDM vs resin 3D printing
- 3DPrinting.com: 3D printing safety guide
- PrintPal: beginner’s guide to FDM 3D printing (a 3D printing company’s guide)
- Snapmaker: how to use a 3D printer, first print walkthrough (a printer maker’s guide)
- Notebookcheck: Elegoo Centauri Carbon 2 Combo review (example of a beginner-friendly enclosed printer, and of software problems)
- 3DWithUs: Elegoo Neptune 4 Pro review (print times)
Facts, prices and links checked against these sources on 16 Nov 2026.



